윤활유 시험목록1

윤활유 시험목록1

 윤활유(오일&그리스) 시험 목록1

Method Number	Method Title
AAR 942	Roll Stability 96 hrs. @ 180° F
ASTM D664	Acid Number, Potentiometric, 2001 or 2004 or 2009 or 2011A version
ASTM D664	Acid Number, Strong, 2001 or 2004 or 2009 or 2011A version
ASTM D128	Analysis of Greases
ASTM D611	Aniline Point
ASTM D128	Aniline Point, Extracted Fluid (+ D611)
AAR M-914 ¶ 2.3.1	Apparent Viscosity ASTM D1092 @ -40°F
API RP 5A3-F	Application/Adherence, Annex F
ASTM D128	Ash Content
ASTM D482	Ash Content of Petroleum Products
ASTM D482	Ash Prep
AN-G-3A	Bleed & Evaporation, 50 hrs. @ 212°F
ASTM D189	Carbon Residue, Conradson of Petroleum Products
ASTM D524	Carbon Residue, Ramsbottom
ASTM D512	Chlorides
ASTM D395	Compression Set of Elastomers
ASTM D938	Congealing Point
ASTM D130	Copper Strip Corrosion - Oil - need time & temperature
ASTM D149	Dielectric Breakdown Voltage & Dielectric Strength of Solid Electrical Insulating Materials -per gap
ASTM D877	Dielectric Breakdown Voltage of Insulating Liquids Using Disk Electrodes (125 ml min.) (Oil)
ASTM D150	Dielectric Constant - AC Loss Characteristics and Permittivity of Solid Electrical Insulation @ Ambi
ASTM D150	Dielectric Constant - AC Loss Charateristics and Permittivity of Solid Electrical Insulation @ Above
ASTM D924	Dissipation (Power) Factor and Relative Permittivity (Dielectric Const.) @ 23°C ± 2°C
ASTM D924	Dissipation (Power) Factor and Relative Permittivity (Dielectric Constant) above 25°C
ASTM D86	Distillation, High Temperature of Petroleum Products
ASTM D566	Dropping Point by Fluid Bath
ASTM D823	Dry Film Performance
ASTM D471	Elastomer Compatibility
ASTM D972	Evaporation Loss @ 6 1/2 hours - need temperature
API RP 5A3-D	Evaporation Test , Annex D
ASTM D381	Existent Gum Content
ASTM D128	Fatty Acid Content
ASTM D93	Flash Point, Pensky-Martens Closed Cup
ASTM D56	Flash Point, Tag Closed Cup, -20°C to 110°C
ASTM D92	Flash AND Fire Points, Cleveland Open Cup
ASTM D92	Flash OR Fire Point, Cleveland Open Cup
ASTM D892	Foaming Characteristics Seq. I
ASTM D892	Foaming Characteristics Seq. I, II, III
ASTM D892	Foaming Characteristics Seq. I,II,III,IV (Mercon)
ASTM D128	Free Alkali/Fatty Acid from Soap
AAR M-914 ¶ 2.3.2	Freezing Point
API RP 5A3-G	Gas Evolution, Annex G
ASTM D287	Gravity, API @ 60°F
ASTM D971	Interfacial Tension @ 20°C or 25°C
ASTM D445	Kinematic Viscosity @ -40°C (w/o solids & solvents) Mil-PRF-63460
AAR M-914 ¶ 2.1	Materials and Consistancy in Brake Cylinder Lubricants
ASTM D127	Melting Point (microcrystalline waxes)
ASTM D87	Melting Point of Waxes
ASTM D128	Moisture Content
AJ 106-2	Molybdenum Disulfide - Ford Method
ASTM D721	Oil Content of Petroleum Waxes
AAR M-914 ¶ 2.4.1	Oil Separation
API RP 5A3-E	Oil Separation Nickel Cone, Annex E
AAR M-914 ¶ 2.6	Oil Swell of Brake Cylinder Elastomers
ASTM D525	Oxidation Induction Period (Gasoline)
ASTM D943	Oxidation Stability (TOST) initial set-up fee (running time additional $4.50 per day)
ASTM D937	Penetration (used for softer unrefined waxes)
ASTM D217	Penetration, Low Temperature, Unworked @ -40°C
ASTM D217	Penetration, Unworked
ASTM D217	Penetration, Worked 60 Stroke
API RP 5A3-C	Penetration, Worked after Cooling, Annex C
ASTM D217	Penetration, Worked Stability, 10,000 Stroke
ASTM D217	Penetration, Worked Stability, Prolonged 100,000 strokes
ASTM D893	Pentane and Toluene Insolubles Procedure A (without coagulant) or Procedure B (with coagulant)
ASTM D128	Percent Soap
ASTM D128	Percent Thickener
ASTM D97	Pour Point
ASTM D91	Precipitation Number
ASTM D942	Pressure Vessel Oxidation @ 100 hours - per run
ASTM D942	Pressure Vessel Oxidation @ 1000 hours per run
ASTM D942	Pressure Vessel Oxidation @ 500 hours - per run
ASTM D665	Rust Preventative Procedure A w/Distilled Water, 4 or 24 hrs.
ASTM D665	Rust Preventative Procedure B w/Synthetic Sea Water, 4 or 24 hrs.
ASTM B117-PTI	Salt Spray Corrosion Test - PTI Specification @ 1000 hours
ASTM B117	Salt Spray Corrosion Test @ 100 hours
ASTM B117	Salt Spray Corrosion Test @ 300 hours
ASTM B117	Salt Spray Corrosion Test @ 48 hours (aka FTM-4001)
ASTM B117	Salt Spray Corrosion Test @ 500 hours
ASTM D94	Saponification Number
ASTM B117-PTI	Soak Test @ 720 hrs.
ASTM D128	Soxhlet Extraction of Oil from Grease
ASTM D70	Specific Gravity
ASTM D891A	Specific Gravity Procedure A Hydrometer @ 20°C
ASTM D891B	Specific Gravity Procedure B Pycnometer @ 20°C
AAR M-914 ¶ 2.3.3	Spreadability
ASTM D217	Storage Stability @ 2 months, Unworked & Worked Penetration
ASTM D217	Storage Stability @ 4 months, Unworked Worked Penetration
ASTM D874	Sulfated Ash
APHA4500	Sulfides
ASTM D638	Tensile Strength of Elastomers
ASTM D323	Vapor Pressure, Reid
ASTM D567	Viscosity Index - calculation with 100°F & 210°F D445 viscosities
ASTM D88	Viscosity Saybolt (SUS) & Calculation (Suggest D2161)
ASTM D445	Viscosity, Kinematic Ambient to 401°F - need temperature
ASTM D445	Viscosity, Kinematic Low Temperature to -65°F - need temp
ASTM D257	Volume Resistivity - D-C Resistance or Conductance of Insulating Materials @ 23°C ± 2°
ASTM D257	Volume Resistivity - D-C Resistance or Conductance of Insulating Materials @ Above 25°C
ASTM D95	Water by Distillation
API RP 5A3-H	Water Leaching, Annex H
AAR M-914 ¶ 2.7.1	Water Stability of Brake Cylinder Lubriants

*참고자료: http://cfile222.uf.daum.net/attach/27739C3657481CFF2B8DC5

*출처: www.anycerti.com

[J]