|
Method Number
|
Method Title
|
|
AAR 942
|
Roll Stability 96 hrs. @ 180° F
|
|
ASTM D664
|
Acid Number, Potentiometric, 2001 or 2004 or 2009 or
2011A version
|
|
ASTM D664
|
Acid Number, Strong, 2001 or 2004 or 2009 or 2011A
version
|
|
ASTM D128
|
Analysis of Greases
|
|
ASTM D611
|
Aniline Point
|
|
ASTM D128
|
Aniline Point, Extracted Fluid (+ D611)
|
|
AAR M-914 ¶ 2.3.1
|
Apparent Viscosity ASTM D1092 @ -40°F
|
|
API RP 5A3-F
|
Application/Adherence, Annex F
|
|
ASTM D128
|
Ash Content
|
|
ASTM D482
|
Ash Content of Petroleum Products
|
|
ASTM D482
|
Ash Prep
|
|
AN-G-3A
|
Bleed & Evaporation, 50 hrs. @ 212°F
|
|
ASTM D189
|
Carbon Residue, Conradson of Petroleum Products
|
|
ASTM D524
|
Carbon Residue, Ramsbottom
|
|
ASTM D512
|
Chlorides
|
|
ASTM D395
|
Compression Set of Elastomers
|
|
ASTM D938
|
Congealing Point
|
|
ASTM D130
|
Copper Strip Corrosion - Oil - need time &
temperature
|
|
ASTM D149
|
Dielectric Breakdown Voltage & Dielectric Strength
of Solid Electrical Insulating Materials -per gap
|
|
ASTM D877
|
Dielectric Breakdown Voltage of Insulating Liquids
Using Disk Electrodes (125 ml min.) (Oil)
|
|
ASTM D150
|
Dielectric Constant - AC Loss Characteristics and
Permittivity of Solid Electrical Insulation @ Ambi
|
|
ASTM D150
|
Dielectric Constant - AC Loss Charateristics and
Permittivity of Solid Electrical Insulation @ Above
|
|
ASTM D924
|
Dissipation (Power) Factor and Relative Permittivity
(Dielectric Const.) @ 23°C
± 2°C
|
|
ASTM D924
|
Dissipation (Power) Factor and Relative Permittivity
(Dielectric Constant) above 25°C
|
|
ASTM D86
|
Distillation, High Temperature of Petroleum Products
|
|
ASTM D566
|
Dropping Point by Fluid Bath
|
|
ASTM D823
|
Dry Film Performance
|
|
ASTM D471
|
Elastomer Compatibility
|
|
ASTM D972
|
Evaporation Loss @ 6 1/2 hours - need temperature
|
|
API RP 5A3-D
|
Evaporation Test , Annex D
|
|
ASTM D381
|
Existent Gum Content
|
|
ASTM D128
|
Fatty Acid Content
|
|
ASTM D93
|
Flash Point, Pensky-Martens Closed Cup
|
|
ASTM D56
|
Flash Point, Tag Closed Cup, -20°C to 110°C
|
|
ASTM D92
|
Flash AND Fire Points, Cleveland Open Cup
|
|
ASTM D92
|
Flash OR Fire Point, Cleveland Open Cup
|
|
ASTM D892
|
Foaming Characteristics Seq. I
|
|
ASTM D892
|
Foaming Characteristics Seq. I, II, III
|
|
ASTM D892
|
Foaming Characteristics Seq. I,II,III,IV (Mercon)
|
|
ASTM D128
|
Free Alkali/Fatty Acid from Soap
|
|
AAR M-914 ¶ 2.3.2
|
Freezing Point
|
|
API RP 5A3-G
|
Gas Evolution, Annex G
|
|
ASTM D287
|
Gravity, API @ 60°F
|
|
ASTM D971
|
Interfacial Tension @ 20°C or 25°C
|
|
ASTM D445
|
Kinematic Viscosity @ -40°C (w/o solids & solvents) Mil-PRF-63460
|
|
AAR M-914 ¶ 2.1
|
Materials and Consistancy in Brake Cylinder Lubricants
|
|
ASTM D127
|
Melting Point (microcrystalline waxes)
|
|
ASTM D87
|
Melting Point of Waxes
|
|
ASTM D128
|
Moisture Content
|
|
AJ 106-2
|
Molybdenum Disulfide - Ford Method
|
|
ASTM D721
|
Oil Content of Petroleum Waxes
|
|
AAR M-914 ¶ 2.4.1
|
Oil Separation
|
|
API RP 5A3-E
|
Oil Separation Nickel Cone, Annex E
|
|
AAR M-914 ¶ 2.6
|
Oil Swell of Brake Cylinder Elastomers
|
|
ASTM D525
|
Oxidation Induction Period (Gasoline)
|
|
ASTM D943
|
Oxidation Stability (TOST) initial set-up fee (running
time additional $4.50 per day)
|
|
ASTM D937
|
Penetration (used for softer unrefined waxes)
|
|
ASTM D217
|
Penetration, Low Temperature, Unworked @ -40°C
|
|
ASTM D217
|
Penetration, Unworked
|
|
ASTM D217
|
Penetration, Worked 60 Stroke
|
|
API RP 5A3-C
|
Penetration, Worked after Cooling, Annex C
|
|
ASTM D217
|
Penetration, Worked Stability, 10,000 Stroke
|
|
ASTM D217
|
Penetration, Worked Stability, Prolonged 100,000
strokes
|
|
ASTM D893
|
Pentane and Toluene Insolubles Procedure A (without
coagulant) or Procedure B (with coagulant)
|
|
ASTM D128
|
Percent Soap
|
|
ASTM D128
|
Percent Thickener
|
|
ASTM D97
|
Pour Point
|
|
ASTM D91
|
Precipitation Number
|
|
ASTM D942
|
Pressure Vessel Oxidation @ 100 hours - per run
|
|
ASTM D942
|
Pressure Vessel Oxidation @ 1000 hours per run
|
|
ASTM D942
|
Pressure Vessel Oxidation @ 500 hours - per run
|
|
ASTM D665
|
Rust Preventative Procedure A w/Distilled Water, 4 or
24 hrs.
|
|
ASTM D665
|
Rust Preventative Procedure B w/Synthetic Sea Water, 4
or 24 hrs.
|
|
ASTM B117-PTI
|
Salt Spray Corrosion Test - PTI Specification @ 1000
hours
|
|
ASTM B117
|
Salt Spray Corrosion Test @ 100 hours
|
|
ASTM B117
|
Salt Spray Corrosion Test @ 300 hours
|
|
ASTM B117
|
Salt Spray Corrosion Test @ 48 hours (aka FTM-4001)
|
|
ASTM B117
|
Salt Spray Corrosion Test @ 500 hours
|
|
ASTM D94
|
Saponification Number
|
|
ASTM B117-PTI
|
Soak Test @ 720 hrs.
|
|
ASTM D128
|
Soxhlet Extraction of Oil from Grease
|
|
ASTM D70
|
Specific Gravity
|
|
ASTM D891A
|
Specific Gravity Procedure A Hydrometer @ 20°C
|
|
ASTM D891B
|
Specific Gravity Procedure B Pycnometer @ 20°C
|
|
AAR M-914 ¶ 2.3.3
|
Spreadability
|
|
ASTM D217
|
Storage Stability @ 2 months, Unworked & Worked
Penetration
|
|
ASTM D217
|
Storage Stability @ 4 months, Unworked Worked
Penetration
|
|
ASTM D874
|
Sulfated Ash
|
|
APHA4500
|
Sulfides
|
|
ASTM D638
|
Tensile Strength of Elastomers
|
|
ASTM D323
|
Vapor Pressure, Reid
|
|
ASTM D567
|
Viscosity Index - calculation with 100°F & 210°F
D445 viscosities
|
|
ASTM D88
|
Viscosity Saybolt (SUS) & Calculation (Suggest
D2161)
|
|
ASTM D445
|
Viscosity, Kinematic Ambient to 401°F - need temperature
|
|
ASTM D445
|
Viscosity, Kinematic Low Temperature to -65°F - need temp
|
|
ASTM D257
|
Volume Resistivity - D-C Resistance or Conductance of
Insulating Materials @ 23°C
± 2°
|
|
ASTM D257
|
Volume Resistivity - D-C Resistance or Conductance of
Insulating Materials @ Above 25°C
|
|
ASTM D95
|
Water by Distillation
|
|
API RP 5A3-H
|
Water Leaching, Annex H
|
|
AAR M-914 ¶ 2.7.1
|
Water Stability of Brake Cylinder Lubriants
|
